Home > Error Code > Kenmore Elite Error Codes F11

Kenmore Elite Error Codes F11

Contents

Undo craig.l Hello, Happy holidays to everyone. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU Cancel Mary Salvador Rep: 13 1 Posted: 01/01/2014 Options Permalink History Thank you for this answer, I took off the top of the washer, the wiring was not exactly as explained, C00 should appear in the display. check over here

These two replacements would have cost close to $500 without a service contract. Like Bookmark August 2, 2008 at 1:18PM Thank you for reporting this comment. Next the blue wire on the LHS of the CCU, last set (back) there are three blue wires. Anyway, I took some very fine sand paper (800 grit) and carefully cleaned off the deposits on both pieces of the contact.

Kenmore F11 Error Code Oven

Please use this interactive troubleshooting guide to determine which component is causing your error code(s). Undo kevintrisha_comcast_net Well my friends, I found out how to fix mine and would like to pass the information on to others. I called again and scheduled service. Not being able to tell for sure I re-soldered it anyway.

this confounded machine is giving me, it looks like I may need to dig into the guts of it. I took the top off the machine, removed the switch unit, and manually pried the latch in and out a few times until it started working smoothly. After visits by 3 different Whirlpool listed repair people the machine was still broken and eventually replaced. Kenmore Elite F1 Error I had to wait a week for the repair appointment.

The solution explains why adding a new board may work, adding a new harness may work, why the error codes are sporadic, why the F11 may occur during heavy or unbalanced With the heavy soil setting, the heater will stay on up to 16 minutes. I am trying to understand what to expect when the tech comes to work on my F11 codes. Just to clarify, I meant to directly reflect and thank you for indicating the ECA LuvMyLabs, and also cross reference the first post by Digitalcandy indicating the same.

Of course, the part was not on the truck. Kenmore Washer F1 Error Code I googled the OMRON relay numbers and found a full spec sheet in .pdf form. Undo runnjump thenotoriousflavio, out of all of the postings I have read on this problem I believe you have hit the nail on the head! I checked out the connections and they seemed okay - but still getting the error.

What Does F11 Mean On My Kenmore Washer

Still getting F11 error. http://he4tf11.blogspot.com/ Yes No Voted Undo Score 11 Cancel Comments: + Great solution, it didn't occur to me that the vibration might break loose the solder joints. 04/24/2011 by mayer the actual relays Kenmore F11 Error Code Oven I live close to the Pacific Ocean with the corrosive salt air so I kind of expect this sort of thing. F11 Error Code Frigidaire Range Undo eliz_always Andrea-weird about the F11 code.

Undo Panamal Thank you twocats. (I have two cats 18# each 5 yrs. check my blog I ordered a door lock online for this model, replaced it, and my problem went away. (At least I thought it did.) After about 6 loads of wash, code F11 now That should get me a good year until that one too fries up. I inspected wire harnesses, reseated connections, etc. Kenmore He3t Whirlpool Duet Board Repair For F11 Code

I insisted that we buy the HE4T because of the great research I did. Add Thread to del.icio.us Bookmark in Technorati Tweet this thread 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Like Bookmark April 1, 2006 at 12:16AM Thank you for reporting this comment. this content ft.

Saved me some serious cash. Kenmore Elite Washing Machine Code F11 Put everything back together, and its worked for 10 + loads so far. SpeakerTweaker 392.008 görüntüleme 10:00 Whirlpool Fault Codes - Süre: 3:39.

When door latch opens the latch coil generates a voltage spike that arcs cross the relay and eventually the contacts don,t hold, especially at the vibrations generated during the final spin

I then put the covers back on both relays and put a little dab of hot melt glue front and back to keep the covers on since the plastic latches broke Undo lcp213nc The F/11 and F/DL codes are a pain in the you-know-what! Funny! Kenmore F1 Error Code Hit PREWASH four times within five seconds, and see C:00 come up on display.

Was this answer helpful? Undo dross In what way can a wiring harness go bad? The relay is undersized and it will undoubtedly fail again. http://wirelessready.org/error-code/kenmore-elite-error-codes-f28.html I have heard of several problems with the wiring harneses being a problem so I think I would start there first.

Undo stumpysan_yahoo_com OK, I still have a question. If I didn't select that, does the machine have a way of detecting or even heating up the water? I then carefully rotated the white box so that I could access the lid and carefully pryed off the lid using a screwdriver. If you do not like to solder, have someone help you...you will have save $$$$$$$.

And as long as I am here again, I would like to take this opportunity once again to thank Sears for not including this board in any of the reference material I assumed since "stack-ability" was a selling point that service could be done to them in that position. Good luck, Chuck Like Bookmark March 10, 2006 at 8:22AM Thank you for reporting this comment. Undo notoriousflavio GOOD NEWS! 15 Months since my Feb 24, 2007 post fix and still working without a single error.

Got numbers 18 10 30 38 across the bottom of the connector, 55 18180 in the red middle section and what looks like 05 606 in very tiny print across the After perusing this forum I decide to go with "thenotoriousflavio" solder solution. THANK YOU "notoriousflavio". This morning I successfully did a load of whites.

My wife then started using cold water cycles successfully. I don't think it has any relays to replace. I've only done one wash so far since, so I hope that takes care of it; so far so good. Because of Lovemylab's post, this was he first thing I replaced, and she is up and running.

Circuit Board Medics 57.599 görüntüleme 3:38 Kenmore Elite HE3T - DLF or F Error Code Fix - Washer Front Load - Süre: 6:54. If you take the board out of the MCU it will be obvious if blown; several resistors were 'smoked' with a black residue on the case. When the guy put his circuit tester into each plug opening, it registered 120. How would I just power on the motor to see if it's working?