Home > Jcl Error > Jcl Error Code 20

Jcl Error Code 20

Contents

Explains in simple language. An I/O error occurred. 14The DCBLRECL field is invalid. 18An invalid Record Descriptor Word was found for an output operation. 30The DCBLRECL field is invalid for MACRF=(PM). 40The DECB is invalid. RCT RECOVERY RECORDS THE ERROR IN SYS1.LOGREC, PERFORMS RESOURCE CLEAN-UP, REQUESTS A SYS1.DUMP OF THE ADDRESS SPACE AND THEN REQUESTS ADDRESS TERMINATION. keep up the good work buddy....ReplyDeleteAnonymousFebruary 22, 2013 at 2:21 AMIf you desire to take a great deal from this piece of writing then you have to apply these methods to http://wirelessready.org/jcl-error/jcl-error-code-list.html

S102 - THE ERROR OCCURRED DURING EXECUTION OF A POST MACRO INSTRUCTION. Following is an example: //CNDSAMP JOB CLASS=6,NOTIFY=&SYSUID,COND=(5,LE) //* //STEP10 EXEC PGM=FIRSTP //* STEP10 executes without any test being performed. //STEP20 EXEC PGM=SECONDP //* STEP20 is bypassed, if RC of STEP10 is A WRITE MACRO WAS ISSUED TO WRITE OUT A BLOCK LARGER THAN THE PRIMARY EXTENT ON THE PREALLOCATED DATASET. S113 - 34 - AN UNSUPPORTED DCB OPTION WAS SPECIFIED FOR A VSAM DATA SET OPENED WITH A DCB.

Rc 4 In Jcl

S0E0 - 29 - AN ALET SPECIFIED AN INVALID ACCESS LIST ENTRY. S002 - 9C - INCORRECT UPDATE WRITE DETECTED. S001 - AN INPUT/OUTPUT ERROR CONDITION WAS ENCOUNTERED DURING EXECUTION OF A CHECK/GET/PUT MACRO INSTRUCTION.

S178 - 20 - AUTHORIZED PRIVATE REQUEST FAILED - PAGE TABLE PAGED OUT. S0FD - A TYPE 6 SVC REQUESTED THE SVC FIRST LEVEL INTERRUPT HANDLER (FLIH) TO SCHEDULE A CROSS MEMORY SRB. E8Only SYSIN and SYSOUT subsystem data sets are supported. RESTART can be accompanied with a checkid, which is the checkpoint written in the dataset coded in the SYSCKEOV DD statement.

S305 - 10 - LSQA STORAGE IS NOT IN THE SUBPOOL SPECIFIED. Jcl Abend Codes The third column contains the text explaining why the Abend may have occurred. S233 - 38 - THE CALLER SPECIFIED THE 4K SQA BUFFER (BUFFER=YES) BUT AN SVC DUMP WAS ALREADY IN PROGRESS. http://ibmmainframes.com/about13421.html THE TWO LOW-ORDER BYTES OF REGISTER 15 CONTAIN A HEXADECIMAL REASON CODE. 2101--A VTAM VALIDITY CHECK OF THE USER'S RPL FAILED BECAUSE THE RPL DOES NOT HAVE THE SAM PROTECTION KEY

So the Return codes (RC) tells the statistics of what happened to the program executed in that step, RC don't belong to JCL but the programs._________________Regards, Anuj Back to top <-- THE ROUTINE WAS GIVEN CONTROL FOLLOWING EXECUTION OF A BSAM CHECK MACRO INSTRUCTION. If theprogram is running disabled, the programmer shoulddetermine whether the storage should be page fixedprior to running disabled, whether the storage areais still obtained through a GETMAIN or whether thestorage address S002 - A0 - INCORRECT ATTEMPT TO ACCESS A PDSE DIRECTORY.

Jcl Abend Codes

One of the following reason codes are associated with the error: 24A Primary Authority Exception occurred. 25A Secondary Authority Exception occurred. 0DA A Program Check Interrupt for a PC Translation http://www.jaymoseley.com/hercules/sabends.htm THE SYSTEM DETERMINED THAT A BUFFER POOL EXISTED FOR THIS DATASET AND MADE THE APPROPIATE TEST SHOWN BELOW WITH UNSATISFACTORY RESULTS: - IF THE DATA WAS TO BE SENT DIRECTLY TO Rc 4 In Jcl SEGMENT MODE IS IMPLIED. Sqlcode Program execution?

IN THE ABNORMAL TERMINATION DUMP, THE TCB FIELD TCBEXCPD (AT OFFSET C0) POINTS TO THE EXCP PROBLEM DETERMINATION AREA. navigate here Hope this helps,d.sch. S240 - 0C - A RDJFCB MACRO INSTRUCTION WAS ISSUED, BUT NO JFCB EXIT WAS SPECIFIED IN THE DCB EXIT LIST. See message TCS015I. 0CAn authorized caller attempted to load a module from a library that is not APF authorized.

The key of the storage can be obtainedusing the IPCS LIST subcommand. B04 An unauthorized caller attempted to GETMAIN storage from a system subpool. THE LENGTH FIELD OF A RECORD DESCRIPTOR WORD (RDW) FOR A VARIABLE LENGTH RECORD SPECIFIES A VALUE LESS THAN 4. Check This Out S118 - INVALID PARAMETERS WERE PASSED TO DEVTYPE (SVC 24). ***IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE*** ***S118 OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S118-RC)**

S130 - THE DEQ MACRO SPECIFIED A RESOURCE NOT PREVIOUSLY SPECIFIED BY BY AN ENQ MACRO. TRY RESTARTING.U1000 - ???U1002 - : A storage allocation failure occurred during initialization.The system attempted to allocate storage for the main NPM control blocks,but insufficient storage was calculated by FNMIN0S0.U1003 - Probably show that you have a missing SYSOUT DD statement.

A message data set was created. 04 (X'04') Successful completion.

S214 - 0C - AN I/O ERROR OCCURRED WHILE PROCESSING A READ BLOCK ID COMMAND TO ESTABLISH THE TAPE POSITION. The reason code is set to 0E. 0CF A Program Check Interrupt for a Floating Point Divide Exception occurred. For QSAM it must be one of: INPUT, UPDATE, OUTPUT or EXTEND. There is a Preview function so you can see your post as it will appea to the forum (rather than how looks in the Editor).

One of the following reason codes are associated with the error: 04The contents of register zero was invalid. 08A parameter was used that requires the caller to be authorized. 0CThe MSGLIST S112 - 01 - PARAMETER LIST NOT IN CALLER'S STORAGE. See message TEC024I. this contact form S10A - 0C - NOT ENOUGH REAL STORAGE FOR SPACE IN LSQA SUBPOOL.

COND=ONLY When COND=ONLY is coded, the current job step is executed, only when any of the previous steps abnormally terminate. Please Vote for good Posts. S121 - A MODULE ISSUED SVC 33 (IOHALT) WITH THE LOW ORDER BIT OF GPR1 OFF, WHICH INDICATES THE PRE-XA (2-BYTE UCB ADDR) INTERFACE. See message TCS010I. 08An unauthorized caller attempted to issue a LOAD to GLOBAL.

The keyof the running program can be obtained from the PSWkey field. S002 - 28 - THE ERROR OCCURRED DURING THE CREATION OF A DIRECT DATASET. The COND can be coded either inside JOB statement or EXEC statement, and in both the cases, it behaves differently as explained below: COND inside JOB statement When COND is coded