Home > Jcl Error > Jcl Errors Mainframes

Jcl Errors Mainframes

Contents

S013 - 44 - AN OPEN MACRO WAS ISSUED FOR A DATASET ON A DIRECT ACCESS DEVICE FOR WHICH CHAINED SCHEDULING WAS SPECIFIED, BUT THE BUFFER CONTROL BLOCK ADDRESS WAS 0. Sometimes, this time limit can also set by internal JES2 or JES3 system. We use this code whenever we open the file, if status code is 00 or 97 we will proceed with our logic, other wise, call error routine. From a utility, only a fool ignores a four. have a peek here

S713 Abend The tape was unexpired and the operator terminated the job. IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S0B0-RC) S0B0 - 04 - INVALID FUNCTION REQUESTED. S222 This abend causing our job to get cancel, because it was suspected of looping or resource unavailability for that job. CLOBBERED IOB OR OTHER SVC PARAMETERS - SEE S0C1 S0F3 - MACHINE CHECK INTERRUPTION DISK I/O FAILURE OR MACHINE TROUBLE S0F8 - THE ISSUER OF AN SVC WAS EITHER IN SRB http://mainframe-wiki.blogspot.com/2011/07/jcl-error-codes-and-abends.html

Jcl Error Codes List Pdf

THE PROGRAM RUNNING AT THE TIME THE OPERATOR PRESSED THE RESTART BUTTON WAS SENT THROUGHABEND PROCESSING BECAUSE THE OPERATOR DETERMINED IT WAS IN A NONCANCELABLE LOOP OR WAIT STATE. S013 - D0 - A DB/DBS RECORD FORMAT WAS SPECIFIED FOR QSAM LOCATE MODE, BUT THE LOGICAL RECORD INTERFACE IS NOT PRESENT IN THE ASSOCIATED BUFFER CONTROL BLOCK; IE. Is there a difference between "sudo apt-get install cuda" and "sudo apt-get install nvidia-cuda-toolkit"?

S104 - 0C - NOT ENOUGH REAL STORAGE FOR SPACE IN LSQA SUBPOOL. S112 - 04 - PROGRAM CHECK OCCURRED IN THE POINT ROUTINE. The data set was on a direct access or magnetic tape device. Jcl Error Cn(internal) S0F8 - 0C - THE SVC ISSUER WAS DISABLED.

Using LABEL=2 when there's only one dataset on the tape. Mainframe Abend Codes List Pdf ddname[-#]DDname (followed by a concatenation number if it is part of a concatenation and not the first DD statement in the concatenation). S913 Abend Security violation. For debugging JCL itself, to the extent you can, you can use TYPRUN=SCAN on your JOB card, or perhaps your site has a JCL-checker product, although these tend to get a

S0CB - DECIMAL DIVIDE EXCEPTION A QUOTIENT EXCEEDS THE SPECIFIED DATA FIELD SIZE. Cobol Error Codes No dump was requested. S013 - B4 - AN OPEN MACRO WAS ISSUED WITH THE INOUT/OUTIN OPTION FOR A DCB SPECIFYING THE QSAM MACRF VALUES; THESE ARE CONFLICTING PARAMETERS. U0456 - IF PSB IS NOT AVAILABLE (NOT RUNNING/SOMEBODY IS USING) WHAT WE SHOULD DO ?

Mainframe Abend Codes List Pdf

S0AE - IOS SUPPORT OF SYSTEM RESTART PROCESSING FOUND THAT THE I/O PURGE MODULE (IGC0001F) WAITING FOR THE COMPLETION OF AN I/O REQUEST. Record greater than 32,768 bytes S013-10 Abend A dummy file with no blocksize. Jcl Error Codes List Pdf S112 - 13 - DCB DOES NOT POINT TO A VALID DEB. Common Jcl Errors S078 - RCT (REGION CONTROL TASK) PROCESSING HAS RECEIVED AN UNACCEPTABLE RETURN CODE FROM AN INVOKED ROUTINE AND CANNOT CONTINUE PROCESSING.

S0B0 - 20 - INVALID BLOCK POINTER (WRITE LOCATE IS ATTEMPTING TO WRITE AND IS PASSING A BLOCK POINTER WHICH IS NOT VALID FOR THE SVA REQUESTED). navigate here S14F - THE ROUTINE ATTEMPTED TO EXECUTE THE STATUS MACRO INSTRUCTION FOR OTHER THAN THE STOP, STOP SYNCH, OR START FUNCTION AND WAS NOT IN SUPERVISOR KEY (0-7). S30A - THE ERROR OCCURRED DURING EXECUTION OF AN R-FORM FREEMAIN MACRO FOR ONE OF THE FOLLOWING REASONS:- A FREEMAIN FOR AN ENTIRE SUBPOOL WAS REQUESTED (REGISTER 1 WAS ZERO) BUT It just means the syntax is OK. 04 means there are "warnings". User Abend Codes In Mainframe

mod The name of the module in which the error occurred. S002 - 5C - AN INTERNAL SAM CONTROL BLOCK (FRQ) USED FOR QUEUING PDSE REQUESTS IS INCORRECT. Same as S013. Check This Out Sx22 Job has been cancelled.

S213 - 20 - DURING AN OPEN, A VOLUME CONTAINED MORE THAN 16 EXTENTS OF THE INDICATED DATASET. Db2 Abend Codes S202 - 08 - FOR A POST IN A USER KEY AND A WAIT IN A SYSTEM KEY, THE ECB TO BE POSTED DOES NOT MATCH ANY ECB BEING WAITED ON. S002 - 58 - AN INTERNAL SAM CONTROL BLOCK (SACB) USED FOR PROCESSING PDSE REQUESTS IS INCORRECT.

For experienced people, MAXCC only exists in IDCAMS (a utility for file and catalog manipulation, defining VSAM files and stuff associated with those types of things).

S013 - 24 - AN OPEN WAS ISSUED WITH INPUT, INOUT, RDBACK, OR UPDATE SPECIFIED, BUT THE DCB MACRF DID NOT SPECIFY EXCP, GET, OR READ. SE37 Abend Insufficient disk space. S137 - 0C - AN I/O ERROR OCCURRED READING A TRAILER LABEL FOR A DATASET OPENED WITH THE INPUT OR INOUT OPTION, OR READING THE HEADER LABEL FOR A DATASET OPENED Iefc452i S130 - THE DEQ MACRO SPECIFIED A RESOURCE NOT PREVIOUSLY SPECIFIED BY AN ENQ MACRO.

The rest of your answer is somewhat confused/confusing. LENGTH REC. S233 - 08 - THE PARAMETER LIST IS NOT A VALID SVC DUMP OR SNAP PARAMETER LIST FOR MVS. this contact form SB37 This is out of space abend.

S013 - 88 - AN OPEN MACRO WAS ISSUED FOR A TELECOMMUNICATIONS DEVICE BUT THE DCBDSORG DID NOT SPECIFY TSO. EITHER A VTAM DESTINATION VECTOR TABLE ENTRY IS INVALID FOR THE DEFINED ATTACHMENT OR VTAM STOARGE HAS BEEN ALTERED.