Home > John Deere > John Deere Cts Error Codes

John Deere Cts Error Codes

Contents

John Deere... E02 1510 13 3 Chopper Vane Angle Sensor out of calibration. E00 1494 08 3 Stuck photo receiver detected in Master Tailings Sensor. E01 1525 11 3 Reel Aft valve driver detects an open, short, over voltage, or over temperature condition. Check This Out

last year We traded for a new 9660, was that a mistake. Power boost is disabled. E01 1539 04 3 HEADERTRAK Angle Sensor (cc# 833) voltage too low - less than 0.5 VDC. Thanks sdgreen is offline Quote Quick Reply post #5 of 11 (permalink) Old 08-30-2008, 11:28 PM sbark Member Join Date: Aug 2007 Posts: 40 Mentioned: 0 Post(s) Quoted: 0 http://manuals.deere.com/omview/OMZ93046_19/OUZXMAG_00018B7_19_10OCT02_1.htm

John Deere 9600 Combine Codes

gben09-09-2005, 08:06 PMdisregard the above post, THE COMBINE IS NOT FIXED!! Injector pump may be damaged because hot fuel loses its lubrication properties. The Left Control Unit 2 will not actuate the Right Sieve Actuator until the fault condition is removed. (Type B only) E04 200342 03 3 A short circuit to ground detected

C00 200011 04 3 CLIMATRAK Solar Sensor voltage is too low - less than 1.5 VDC. Turn Key Switch to the OFF position. MostlyGreen09-02-2005, 01:39 PMI share your sentiment, Papaw, although I was an IH Axial Flow fan from 1979 up until 1997, then I traded for a Deere 9610, which was a very John Deere Diagnostic Codes E02 1510 03 3 Chopper Vane Angle Sensor (cc# 781) voltage is too high (above 4.97 VDC).

Finally DTAC spent two hours on the phone to the tech with his equipment and decided the board in the post readouts was bad. $595 later and a 50 mile trip John Deere 9600 Error Codes E01 1079 03 2 Height Sensor Power (cc# 481) voltage is too high - greater than 5.25VDC. I am not at all convinced that it was lightning but maybe. E00 1493 11 3 Tailings system failure.

E02 1565 09 3 CAN Bus message missing from Armrest Control Unit - Discrete Input Status OUZXMAG,00018B7 -19-10OCT02-21/25 E03 - Left Control Unit Diagnostic Trouble Codes Control Unit SPN FMI John Deere Cheat Codes Device or wiring is faulty. A00 97 04 2 Water in Fuel Sensor (cc# 136) voltage out of range low. Faulty device or wiring.

John Deere 9600 Error Codes

C00 627 03 1 Delayed Power (cc# 006) voltage is above 16 VDC. http://www.docs-engine.com/pdf/1/john-deere-fault-codes-f9p8.html C00 1547 03 3 CLIMATRAK Core Temperature Sensor voltage too high - greater than 4.47 VDC. John Deere 9600 Combine Codes Description A00 91 09 3 Throttle input not valid or not received A00 94 03 1 Fuel Pressure Sensor (cc# 131) voltage out of range high - greater than 4 VDC John Deere Combine Error Codes OUZXMAG,00018B7 -19-10OCT02-7/25 To read and record diagnostic trouble codes press the enter switch.

A00 1347 10 2 Pump Solenoid 1 is not delivering expected fuel flow. http://wirelessready.org/john-deere/john-deere-error-code-57.html E01 1079 04 2 Height Sensor Power (cc# 481) voltage is too low - less than 4.75VDC. A00 652 07 2 The fuel flow to cylinder #2 is lower than expected. Faulty device or wiring. John Deere Diagnostic Code Reader

E03 200134 11 1 The Left Marker Light driver detects an open, short, over voltage, or over temperature condition. Faulty device or wiring. Gleaner, Massey Ferguson, White Combines ... http://wirelessready.org/john-deere/john-deere-error-codes-67.html RECEIVE 50% OFF ONE COMBINE HEADER INSPECTION ....

File link: http://s3.amazonaws.com/m...s%20Manual%20(955125).pdf 94% Download our online catalog. John Deere Ecu Codes A00 1569 31 2 Engine protection - power derated due to other faults. Just have to wait and see I guess but it is finally back in the field and APPEARS to be working normally.

I know you already replaced the harness nearest the pump.

C03 1487 04 3 Dimmer voltage is too low - less than 0.5 VDC. Custom Harvesters Walinga USA Wilger Reynolds Farm Equipment Calibrated Power Solutions Brandt Group of Companies McMunn & Yates Building Supplies thecombineforum.com Forum Tech Support thecombineforum.com Forum Help Desk Active Topics Today's C00 1504 11 1 The Seat Switch has been closed continuously for 6 hours. Brew, I'm trying to find some info on the other codes, there might be a chance the codes you are seeing are a 2 part code - do you know how

Kevin is online now my john deere 9500 is bucking bad and 34e and 35e codes are This answer was rated: ★ ★ ★ ★ ★ my john deere 9500 Replace the Right Control Unit if condition persists. C00 628 12 1 Controller cannot exit boot block program. navigate here Device or wiring is faulty.

Wait for 30 seconds. Replace Left Control Unit if condition persists. The device or wiring is faulty.